WTB 2.5"x2.5"x.25" wall

Post by **alk1174** » Thu Apr 05, 2007 3:46 pm

Looking for a 2' peice of 2.5"x2.5"x.25" wall square tube. Anyone got apeice they are willing to sell?

Post by **jonesy** » Thu Apr 05, 2007 5:17 pm

i have some at my parents house .... i think i have about 15 feet of it actually ... if you can wait for it ill cut you what you want ... figure bout $8 would be fair .... it is welded though, so it has the seam inside if that matters at all for your application

Post by **alk1174** » Thu Apr 05, 2007 5:33 pm

affende wrote:i have some at my parents house .... i think i have about 15 feet of it actually ... if you can wait for it ill cut you what you want ... figure bout $8 would be fair .... it is welded though, so it has the seam inside if that matters at all for your application

That would be great. When are you planning on making a trip that way?

Post by **jonesy** » Thu Apr 05, 2007 10:19 pm

alk1174 wrote:
affende wrote:i have some at my parents house .... i think i have about 15 feet of it actually ... if you can wait for it ill cut you what you want ... figure bout $8 would be fair .... it is welded though, so it has the seam inside if that matters at all for your application
That would be great. When are you planning on making a trip that way?

i will be going down one week from today and returning on saturday

Post by **Arya Ebrahimi** » Fri Apr 06, 2007 2:37 am

I'd be down for some too Cody if you have enough and don't mind.

Post by **jonesy** » Fri Apr 06, 2007 2:45 am

Arya Ebrahimi wrote:I'd be down for some too Cody if you have enough and don't mind.

how much you want?

Post by **jonesy** » Fri Apr 06, 2007 2:47 am

and i also have 10 feet of 2x2x.250 wall if any one needs it .... just let me know how much ... both will be a bout $4 a foot i do believe ....

Post by **Arya Ebrahimi** » Fri Apr 06, 2007 3:52 am

affende wrote:
Arya Ebrahimi wrote:I'd be down for some too Cody if you have enough and don't mind.
how much you want?

Enough to make a driveshaft. 2'? 3'? something like that.

Post by **jonesy** » Fri Apr 06, 2007 1:25 pm

Arya Ebrahimi wrote:
affende wrote:
Arya Ebrahimi wrote:I'd be down for some too Cody if you have enough and don't mind.
how much you want?
Enough to make a driveshaft. 2'? 3'? something like that.

lol ... well you get me a number you want and ill cut it that length for you .... that way when its too short, i wasnt the one that decided the length

is this for the front DS on the yota?

Post by **Arya Ebrahimi** » Fri Apr 06, 2007 2:08 pm

affende wrote:is this for the front DS on the yota?

Yes. I'll do some research and get back to you, unless Krantz knows what should be sufficient?

Post by **alk1174** » Fri Apr 06, 2007 4:28 pm

On my first square shaft I used to 14" pieces, but this was with the L52 trans which is pretty short. I think 2' should be plenty. Cody I think 2' is all I need but I will measure and let you know soon. I can also give you money up front if you need it for gas money just let me know.

Post by **jonesy** » Sat Apr 07, 2007 12:43 am

not a problem guys ... just gimem the numbers you want ill chop it up and bring it back with me ....

Post by **alk1174** » Mon Apr 09, 2007 8:05 am

affende wrote:not a problem guys ... just gimem the numbers you want ill chop it up and bring it back with me ....

2' will work fine for me, let me know when and where to bring you the cash.

Post by **jonesy** » Mon Apr 09, 2007 2:57 pm

alk1174 wrote:
affende wrote:not a problem guys ... just gimem the numbers you want ill chop it up and bring it back with me ....
2' will work fine for me, let me know when and where to bring you the cash.

aight ... will do.

Post by **BlueDodgeRam** » Mon Apr 09, 2007 11:38 pm

cody, do you happen to go near knoxville going to or from blacksburg?

wonderin if itd be possible for ya to pick up 4 tires if i provide some fuel $$