Sinking Creek 4WD Association

Posted: **Fri Feb 18, 2011 12:14 pm**

BadnewsCJ wrote: Does anyone (Will...) have 60 set up bearings here in Blacksburg?

Yes, I'll bring them by today

Posted: **Fri Feb 18, 2011 6:08 pm**

BadnewsCJ wrote:If anyone needs any diff parts for their build, I have to recommend RPM Offroad. Sent my paypal in 11:00 Tuesday morning and my gears, spool, and install kits showed up Wednesday afternoon. With great prices too. And some of those parts had to be dropped shipped.

Does anyone (Will...) have 60 set up bearings here in Blacksburg?

RPM Offroad for real dude

They beat all other quotes for my swampers by like $250 and they were at my house 48 hours after I called the order in

Posted: **Fri Feb 18, 2011 7:07 pm**

I got the tires on my diesel from RPM Offroad. Gave me a hell of a deal.

Posted: **Sat Feb 19, 2011 8:59 am**

Got the motor running last night. It runs so well it won't shut off...need to figure out why that is. And coolant blows out my passenger side header. Lovely, guess I get to do head gaskets soon.

Posted: **Sun Feb 20, 2011 4:54 pm**

Trong art

Posted: **Thu Feb 24, 2011 3:08 pm**

We should start some bending this weekend

Posted: **Fri Feb 25, 2011 9:39 am**

http://midmoracing.com/bendit.htm

this is where I downloaded that program Nick

Posted: **Sat Feb 26, 2011 9:16 am**

dodgeguy119 wrote:We should start some bending this weekend

Indeed. I'm headed out to cburg now to get the torches back from Alec so I can cut the stock roll bar out. I'll be in the garage till tonight playing with the bender. And then all next week hopefully.

Posted: **Sun Feb 27, 2011 8:11 pm**

For those not in blacksburg, cause I'm pretty sure the whole club was at the moontower at some point this weekend, we got some tubework done. Made a grill hoop to test out the bender, then got a decent bit done on the cage. Big thanks to Will and Zach for helping me out.

Posted: **Sun Feb 27, 2011 8:49 pm**

Looks awesome!! Good job!

Posted: **Mon Feb 28, 2011 10:34 am**

Oh, and it appears as though it may fit out of the garage. 80 ish inches to the top of the cage, 84 inches to the top of garage door opening

I'm going to put a bend in the A pillar spreader to get the angry bar look. Thoughts on using two pieces of 1.5 as the angry bar's tying in the spreader to the dash bar? Will has two pieces of 1 inch, and I'm thinking maybe 1.5 will be too much. I'll see if I can get some pictures up by this evening to better explain.

Posted: **Mon Feb 28, 2011 10:35 am**

BadnewsCJ wrote:Got the motor running last night. It runs so well it won't shut off...need to figure out why that is. And coolant blows out my passenger side header. Lovely, guess I get to do head gaskets soon.

Good news in regards to this. Leaky hose resulted in the appearance of coolant leaking from my passenger side head right by the header. As far as I can tell both head gaskets are still good to go. Yippie.

Posted: **Mon Feb 28, 2011 10:39 am**

Cut a piece out of the 1.5" lengthwise and weld it back together so it looks like this ()

Posted: **Mon Feb 28, 2011 11:51 am**

I have a 1.5" die if that will help.

Posted: **Mon Feb 28, 2011 3:06 pm**

Ary...are you saying to cut it out weld back together so it has less of a cross section at the ends and is a fatty in the middle?

Krantz...thanks for the offer but I bought one when I got my bender, figured I would need it to do my fenders, seat mounts, gussets, etc.

Sinking Creek 4WD Association

Nick's CJ