Sinking Creek 4WD Association

Posted: **Fri Feb 01, 2013 11:38 am**

I'd be interested in trying that pump if you don't have plans for it. How much are you looking to get?

Posted: **Fri Feb 01, 2013 9:44 pm**

Username wrote:That's still 2000 RPM more than you slick.

Lol, touche.

Posted: **Sun Feb 24, 2013 10:13 pm**

Ordered fuel system stuffs.

Welded all my tabs for the roof and firewall as well as started on a B-pillar X behind the seats. Also seriously considering KOH tech spec A-pillars (an additional vertical brace running directly down from the top of the bend.

Posted: **Thu Feb 28, 2013 9:17 am**

Got all the remaining parts into finish up my fuel system. Going to run a Walbro 255lph pump, which a lot of ultra 4 rigs seem to have luck with. I figure since most of them have significantly more motor than I do, it should work fine for me.

Also finished up the B-pillar X and test fit the firewall and fuel cell.

Its getting close..

Posted: **Thu Feb 28, 2013 9:48 am**

Nice location, you gonna build a bed for cargo space (you may already have and I wasn't paying attention).

Posted: **Thu Feb 28, 2013 10:17 am**

Looking good, are going going to put the expanded steel floor back in after you finalize fuel cell mount? Are going to put the roof on for Windrock

Posted: **Thu Feb 28, 2013 10:47 am**

CJonLP wrote:Nice location, you gonna build a bed for cargo space (you may already have and I wasn't paying attention).

I have a perforated steel floor setup for it now, but I will likely change it a little bit now that the cell is there taking up so much space.

Posted: **Thu Feb 28, 2013 10:48 am**

Matt612 wrote:Looking good, are going going to put the expanded steel floor back in after you finalize fuel cell mount? Are going to put the roof on for Windrock

See above, and yeah, definitely going for the roof. All the mounts are ready, just needs to be trimmed/formed/drilled and bolted down

Posted: **Thu Feb 28, 2013 12:37 pm**

I like the dual B-pillar X with separate fancy pants harness bar. I think you should leave it like that since the cage was strong enough to hold up to a hard roll before adding the additional strength.

Posted: **Fri Mar 01, 2013 1:46 pm**

i agree with Alec ^^ fancy harness bar

Posted: **Fri Mar 01, 2013 2:51 pm**

the x will definitely help with lateral stability.

Is your fuel cell an RCI 2161?

Posted: **Sun Mar 03, 2013 8:08 pm**

Jay12 wrote:the x will definitely help with lateral stability.

Is your fuel cell an RCI 2161?

Yes sir it is. I used to run a standard 16 gallon squre with a sump but switched to the 2161 to free up some space.

got the mount for the cell but together tonight.

Posted: **Wed Mar 06, 2013 6:44 pm**

Posted: **Thu Mar 14, 2013 1:08 pm**

Finished fuel cell set up. Cooler and action packer fit great.

Posted: **Thu Mar 14, 2013 1:38 pm**

Shameless copy of fuel cell mount design and vent cutoff ball valve on my part.

Sinking Creek 4WD Association

YJ goes under the knife

Re: YJ goes under the knife

Re: YJ goes under the knife

Re: YJ goes under the knife

Re: YJ goes under the knife

Re: YJ goes under the knife

Re: YJ goes under the knife

Re: YJ goes under the knife

Re: YJ goes under the knife

Re: YJ goes under the knife

Re: YJ goes under the knife

Re: YJ goes under the knife

Re: YJ goes under the knife

Re: YJ goes under the knife

Re: YJ goes under the knife

Re: YJ goes under the knife