Sinking Creek 4WD Association

The build keeps getting better, Nice...I might have to check out those seats and Potts this weekend. Im in the market for some here soon and I would like to keep the cost to a minimum.

Nice build! I like the seats and may consider a hand throttle for my 97 TJ soon!

tomg wrote:Nice build! I like the seats and may consider a hand throttle for my 97 TJ soon!

Yep. Me too. I've already looked into the parts haha.

Matt612 wrote:The build keeps getting better, Nice...I might have to check out those seats and Potts this weekend. Im in the market for some here soon and I would like to keep the cost to a minimum.

Theres more build to come, I just dont have time to put it all up in one night!

The seats are great if your butt isnt too wide. They are a little snug on my buns, which dosent really bother me unless we are talking about 3+ hours in them on the highway. Trails arent bad because of the constant getting in and out. See you this weekend.

MtnManMatt wrote:

tomg wrote:Nice build! I like the seats and may consider a hand throttle for my 97 TJ soon!

Yep. Me too. I've already looked into the parts haha.

By far, the hand throttle has been the cheapest mod to date! Its a little tricky to hook up under the hood, sometime Ill show you how I did it.

Picked up a set of 4" OME coils to replace my 3.5" RE coils.

Front, before and after, gained about 0.75"

Rear, before and after, gained about 1.00"

Started prepping the interior for The Raptor spray-on bedliner.

Finished the U-Pol Raptor Liner project.
Full write up available here,
http://novajeepers.net/index.php?topic=7981.0

Nexy up... The Savvy Gas Tank Skid. This is made of aluminium and only weighs 4 lbs more than the stock skid.
It offered 2 mounting heights so with my body lift I can gain additional clearance.

The old tank was a really tight squeeze into the new skid but it is designed that way.

And Installed.

A few before and after shots.

Savvy advertises 1.5 inches. I got almost 2!!

I got a set of JKS miniskids for the front lower control arms from Steve at Jeeps Xtreme in Fredericksburg.
Had Seth at Pineridge auto weld them on for me.

And thats about where she sits today.
Currently, I am in the middle of removing, sanding and spraying the body armour with duplicolor spray on bed liner to act as a rust preventer and for easy touchups after trips.
Already finished the front bumper and the rocker guards. Coming soon, rear bumper/tire carrier. Pics may follow.

Next major mod........
Coming soon???
Hood line fenders with 3" flare??

So last fall I decided I wanted some bling.
So I added some grill lights and some underglow.
All I have a picture of is the grill lights. It was a pretty simple job, a relay and a switch and a few hours running and hiding wires and this is what I got.

Tax return this year finally brought the hoodline fenders I always wanted. So in preparation, first off was to remove the rock rails and this is what I found.



So needless to say I am refinishing those right now!
Also was able to media blast an old set of springs to get them ready for new paint thanks to Alec's Sooper Dooper fab works in Christiansburg. This is what they looked like before the blast.



Media blasting is not any fun, actually it pretty much sucks ass sideways and I will never do it again. If you ask me it is easily worth $30+ an hour and I will not hesitate to pay someone next time!

And the C&C Fabs Hoodline fender with 3" flare is getting painted. started with self-etching primer and then a can of white to match the Jeep. Then the weather got sucky again and cant paint more till it warms up again. Heres how they look right now.



Stay tuned more to come in the next few weeks.