WTB 2.5"x2.5"x.25" wall
Posted: Thu Apr 05, 2007 3:46 pm
Looking for a 2' peice of 2.5"x2.5"x.25" wall square tube. Anyone got apeice they are willing to sell?
Sinking Creek 4WD Association
Off-Roading In The New River Valley
http://sc4wda.org/forums/
WTB 2.5"x2.5"x.25" wall
Page 1 of 2
Posted: Thu Apr 05, 2007 5:17 pm
i have some at my parents house .... i think i have about 15 feet of it actually ... if you can wait for it ill cut you what you want ... figure bout $8 would be fair .... it is welded though, so it has the seam inside if that matters at all for your application
Posted: Thu Apr 05, 2007 5:33 pm
That would be great. When are you planning on making a trip that way?affende wrote:i have some at my parents house .... i think i have about 15 feet of it actually ... if you can wait for it ill cut you what you want ... figure bout $8 would be fair .... it is welded though, so it has the seam inside if that matters at all for your application
Posted: Thu Apr 05, 2007 10:19 pm
i will be going down one week from today and returning on saturdayalk1174 wrote:That would be great. When are you planning on making a trip that way?affende wrote:i have some at my parents house .... i think i have about 15 feet of it actually ... if you can wait for it ill cut you what you want ... figure bout $8 would be fair .... it is welded though, so it has the seam inside if that matters at all for your application
Posted: Fri Apr 06, 2007 2:37 am
I'd be down for some too Cody if you have enough and don't mind.
Posted: Fri Apr 06, 2007 2:45 am
how much you want?Arya Ebrahimi wrote:I'd be down for some too Cody if you have enough and don't mind.
Posted: Fri Apr 06, 2007 2:47 am
and i also have 10 feet of 2x2x.250 wall if any one needs it .... just let me know how much ... both will be a bout $4 a foot i do believe ....
Posted: Fri Apr 06, 2007 3:52 am
Enough to make a driveshaft. 2'? 3'? something like that.affende wrote:how much you want?Arya Ebrahimi wrote:I'd be down for some too Cody if you have enough and don't mind.
Posted: Fri Apr 06, 2007 1:25 pm
lol ... well you get me a number you want and ill cut it that length for you .... that way when its too short, i wasnt the one that decided the lengthArya Ebrahimi wrote:Enough to make a driveshaft. 2'? 3'? something like that.affende wrote:how much you want?Arya Ebrahimi wrote:I'd be down for some too Cody if you have enough and don't mind.
is this for the front DS on the yota?
Posted: Fri Apr 06, 2007 2:08 pm
Yes. I'll do some research and get back to you, unless Krantz knows what should be sufficient?affende wrote:is this for the front DS on the yota?
Posted: Fri Apr 06, 2007 4:28 pm
On my first square shaft I used to 14" pieces, but this was with the L52 trans which is pretty short. I think 2' should be plenty. Cody I think 2' is all I need but I will measure and let you know soon. I can also give you money up front if you need it for gas money just let me know.
Posted: Sat Apr 07, 2007 12:43 am
not a problem guys ... just gimem the numbers you want ill chop it up and bring it back with me ....
Posted: Mon Apr 09, 2007 8:05 am
2' will work fine for me, let me know when and where to bring you the cash.affende wrote:not a problem guys ... just gimem the numbers you want ill chop it up and bring it back with me ....
Posted: Mon Apr 09, 2007 2:57 pm
aight ... will do.alk1174 wrote:2' will work fine for me, let me know when and where to bring you the cash.affende wrote:not a problem guys ... just gimem the numbers you want ill chop it up and bring it back with me ....
Posted: Mon Apr 09, 2007 11:38 pm
cody, do you happen to go near knoxville going to or from blacksburg?
wonderin if itd be possible for ya to pick up 4 tires if i provide some fuel $$
wonderin if itd be possible for ya to pick up 4 tires if i provide some fuel $$