D-ring Shackle Mounts

Wrenching and Technical Information

Moderator: Club Officers

Post Reply
User avatar
Ctrow
Posts: 1411
Joined: Wed Mar 29, 2006 10:22 am
Location: Gods Country

D-ring Shackle Mounts

Post by Ctrow »

Does anyone know where I can get some weld-on cleivs D-ring mounts? Tryig to add some to my front bumper.
1987 MJ, "Trowmanche v2.0"
1998 Cummins
2012 Jeep Compass (Mals)
User avatar
yotacowboy
Posts: 581
Joined: Thu Dec 16, 2004 6:28 am
Location: b'burg
Contact:

Post by yotacowboy »

call up BTF, i'm pretty sure they've got some.
'91 Reg. Cab Yota DD: DOA 22re RV, .060 over,270 cam,ported,Thorley Tri-Y,2.25 cat,Flowey 40,SAS'd,Locked,Longed,Pig'd,Bumpered,Slidered,Sky wide axle,5.29's,Duals,Sky Tcase skid,37" Iroks,2.5" BS blk steelies,Allpro Hy-steer,HighAngle D-lines
User avatar
Username
Posts: 172
Joined: Wed Dec 15, 2004 9:59 am
Location: passed out on the couch

Post by Username »

BTFs are nice. 1" thick and contoured to fit tubes. I have an extra set of thier 1/2" thick mounts they install on their bumpers. They sent me them by mistake and I have no use for them. PM or email me if you want them.
User avatar
Ctrow
Posts: 1411
Joined: Wed Mar 29, 2006 10:22 am
Location: Gods Country

Post by Ctrow »

found a site www.rokmen.com they're $10 each and free shipping if you buy 6
1987 MJ, "Trowmanche v2.0"
1998 Cummins
2012 Jeep Compass (Mals)
User avatar
Trailduster79
Posts: 438
Joined: Tue Dec 14, 2004 10:41 pm
Location: The shitty real world

Post by Trailduster79 »

I know it has been a while since this post was posted, but hit up Tractor Supply in C'burg. That's where I got mine from.
79 Trailduster 360\727\203\NP205 - 60's 5.13's detroit/welded - 38.5 SX's - 12K winch

88 Samurai - RIP

06 3500 Quad Cab Long Bed 4x4 Cummins Edge Juice/attitude, billet tranny, muffler delete
CRAWL3R TJ

Post by CRAWL3R TJ »

Trailduster79 wrote:I know it has been a while since this post was posted, but hit up Tractor Supply in C'burg. That's where I got mine from.
I don't believe they sell the mounts that you weld to the bumper, unless I haven't seen them yet.

Tractor Supply does carry the D-ring shackle. You can get either the Warn for about $22 and about a 3 ton rating or go with the generic brand for $13 with about a 6.5 ton rating. Northern also carries the 6.5 ton shackle for $10. Those are the ones I bought for my recovery needs.
currupt4130

Post by currupt4130 »

I've got a buddy that makes them. He's fairly cheap. If you want his info pm me. They're 3/4" thick, and about 4 inches long. Good for putting all the way through a bumper.
User avatar
Trailduster79
Posts: 438
Joined: Tue Dec 14, 2004 10:41 pm
Location: The shitty real world

Post by Trailduster79 »

I know mine came from there cause that is where I got them from.

I will see if I can dig some pictures of them up.

BRB
79 Trailduster 360\727\203\NP205 - 60's 5.13's detroit/welded - 38.5 SX's - 12K winch

88 Samurai - RIP

06 3500 Quad Cab Long Bed 4x4 Cummins Edge Juice/attitude, billet tranny, muffler delete
User avatar
Trailduster79
Posts: 438
Joined: Tue Dec 14, 2004 10:41 pm
Location: The shitty real world

Post by Trailduster79 »

here is a pic of my bumper with the D-ring mounts I got from tractor Supply. Granted it was about 2-3 years ago, but non the less, I got them from TC[/img]
Attachments
index.jpg
index.jpg (15.61 KiB) Viewed 3399 times
79 Trailduster 360\727\203\NP205 - 60's 5.13's detroit/welded - 38.5 SX's - 12K winch

88 Samurai - RIP

06 3500 Quad Cab Long Bed 4x4 Cummins Edge Juice/attitude, billet tranny, muffler delete
Post Reply