De-clutter My Shop Sale!

Parts, vehicles, fab and mechanic work, etc.

Moderator: Club Officers

User avatar
Billet Benny
Posts: 398
Joined: Fri Jan 07, 2005 7:30 pm
Location: Sinking Creek

De-clutter My Shop Sale!

Post by Billet Benny »

I'm going to get rid of all my saved up stuff that I don't 100% need for the current project. I need the space, the money, and the relief of not having such a big pile of stuff. All prices obo. I'm gonna list up all the stuff I can think of and can give/get more details as requested. Some kind of non refundable deposit will be required for some of this so I don't haul it up to B'burg for nothing.

Buggy Chassis seriously for sale now. V30 shortened frame, 2" .120 wall DOM. Comes with 63" rear Chevy leaf springs in the rear and the never ridden on small lift 1/2 ton truck front leaf springs... $750

Complete FF 14 bolt from the rear of the buggy. 3.73 gears with welded diff. Cleaned and painted, no rust. Disc brakes with Shaker disk brake brackets and new calipers, pads, and rotors. The unpainted calipers and rotors did rust but would work fine after a few stops. No brake lines. Other than that it's complete with the factory stuff of an '87 14 bolt in a one ton (i.e. it has one ton spring pad spacing)... $300

Had a junkyard 14 bolt I started building.. Gonna sell the parts:
14 bolt short side shaft $35
14 bolt long side shaft $35
14 bolt housing only.. bead blasted and painted. wears a BTF truss with the matching pinion guard.. holes have not been drilled yet to mate truss to pinion guard, will take a little fab. Truss is welded on by me. All other factory mounts removed. Comes with 4 tabs to be welded on top of truss for 2 upper link mounts. Also includes new pinion bearing races and seal installed in the pinion housing. $200 SOLD
14 bolt open carrier, no gears. $40 SOLD
14 bolt 4.88 thick gears brand new with master install kit I began using.. pinion has new bearing installed.. $175 SOLD What's left of install kit still around. Carrier bearings, crush collar, third pinion bearing, et al. .. $35
14 bolt 1410 ubolt yoke ubolt style.. $80
14 bolt hubs bead blasted and painted.. pair. No studs or bearings.. $50 SOLD

TH400 transmission. Originally mated to NP203.. Was told it worked fine but have never run it. Looks to be good and I trusted the guy.. Complete with torque converter.. $275

NP203 that was originally mated to a TH350. Good for range box for doubler.. $100

Toyota IFS truck steering box.. $80

Sky Manufacturing flat billet Toyota ifs box pitman arm... Tapered for Chevy tierod end. Never installed. $80 SOLD

Drag link 1.25" od .250 wall tapped for chevy tierod ends. Can get length if u have a use but it was for use in the buggy when i was going to run a steering box.. so with a full width axle.. Also was to use the long drag link chevy ends.. I have those new and they can go with it.. $60 SOLD

Dana 60 kingpin steering arm.. Sky Manufacturing part for use with Chevy tapered ends.. Never installed. $100 SOLD

Wrecked '92 Yamaha Seca II 600cc motorcycle. Ran very bad after wreck.. Tank dented and handle bars bent.. Some scratches on the right side.. Red.. $500

Dana 80 from Dodge 2500.. bead blasted and primered for rust protection.. drum brakes that would need replacing, but axle is complete.. $550

Dodge dually Dana 60 hubs. Wheels studs aren't good.. External style with one broke bolt in each hub.. $50 pair SALE PENDING

FF 14 bolt Used gearset 3.73's. A little tooth rust.. $25

AMC 360 to chevy automatic transmission adapter kit. Advance adapters make. Uses an adapter plate between the motor and transmission and I have the correct flexplate to work with a 360 and th350.. Never been installed. $150

Toyota ifs hubs. Bare. Pair.. $40

Bushnell Rifle Scope. Old 3x-9x 40mm Bushnell Sportview scope. It's the cheap model. Had it on a .270 for almost 10 years now and it always held zero consistently over the years. $40..

Weaver 1" Detachable scope rings. One ring is an extension ring. $15

Weaver bases. One's a 46 and the other a 47. $5 for both.

Have a CBR 600rr aluminum swing arm. $75

More to be added as I dig it out.
Last edited by Billet Benny on Tue Apr 08, 2008 2:43 pm, edited 16 times in total.
Benny
'98 Taco
'05 Taco
'00 Cummins
User avatar
JCaldwell
Posts: 155
Joined: Thu Mar 01, 2007 9:54 am
Location: Craig County
Contact:

Hubs

Post by JCaldwell »

Hey man are those factory hubs? Big or small?
85 K20 short bed chevy 8in's 38.5 boggers (toy)
74 K20 6in's 35 boggers
72 K20 6in 454 (Project)
98 cummins ext cab built
95 K20 chevy on 35's
92 2wd yoyo 2.5in's
04 660 Grizzly,03 Eiger,06 450R Honda
User avatar
Billet Benny
Posts: 398
Joined: Fri Jan 07, 2005 7:30 pm
Location: Sinking Creek

Post by Billet Benny »

JCaldwell,

I assume you mean the 14 bolt hubs. They're factory from the parted out 14 bolt. Here is a photo. Yea, I painted 'em green after getting beadblasted.

They are the srw style and not the cab and chassis style. Called "type A" in BillaVista's 14 bolt bible. Sidenote, you can find my name in that bible as well as Clay's. :flipoff2: famous!
Attachments
14 bolt hubs.JPG
14 bolt hubs.JPG (91.42 KiB) Viewed 8101 times
Benny
'98 Taco
'05 Taco
'00 Cummins
tsmall07
Posts: 753
Joined: Wed Jan 26, 2005 4:10 pm
Location: Blacksburg VA
Contact:

Post by tsmall07 »

Holy crap dude! Thats a lot of chit. If you dig out a 205, I'll take it!
"The American Indians found out what happens when you don't control immigration."

"Calling an illegal alien an undocumented immigrant is like calling a drug dealer an unlicensed pharmacist"
User avatar
Billet Benny
Posts: 398
Joined: Fri Jan 07, 2005 7:30 pm
Location: Sinking Creek

Post by Billet Benny »

Tyler,
Just sold the last 205 about a month ago to Caleb.. But if another one rolls out of the corner I'll let you know.
-B
Benny
'98 Taco
'05 Taco
'00 Cummins
User avatar
JCaldwell
Posts: 155
Joined: Thu Mar 01, 2007 9:54 am
Location: Craig County
Contact:

Post by JCaldwell »

Thanks man for the pic I'll let you know sumthing...U got any 4.56 gears for a 14blt? or whole axle?
85 K20 short bed chevy 8in's 38.5 boggers (toy)
74 K20 6in's 35 boggers
72 K20 6in 454 (Project)
98 cummins ext cab built
95 K20 chevy on 35's
92 2wd yoyo 2.5in's
04 660 Grizzly,03 Eiger,06 450R Honda
User avatar
Billet Benny
Posts: 398
Joined: Fri Jan 07, 2005 7:30 pm
Location: Sinking Creek

Post by Billet Benny »

JCaldwell wrote:Thanks man for the pic I'll let you know sumthing...U got any 4.56 gears for a 14blt? or whole axle?
I'll check but I don't think so.. The factory set could be, but the chances are low.. Just 3.73's and 4.88's for sure.
Benny
'98 Taco
'05 Taco
'00 Cummins
User avatar
jac6695
Posts: 427
Joined: Mon Mar 05, 2007 3:19 pm
Location: C'Burg

Re: De-clutter My Shop Sale!

Post by jac6695 »

Billet Benny wrote:
Had a junkyard 14 bolt I started building.. Gonna sell the parts:
14 bolt short side shaft $35
14 bolt long side shaft $35
14 bolt housing only.. bead blasted and painted. wears a BTF truss with the matching pinion guard.. holes have not been drilled yet to mate truss to pinion guard, will take a little fab. Truss is welded on by me. All other factory mounts removed. Comes with 4 tabs to be welded on top of truss for 2 upper link mounts. $200
Benny,

Is this the BTF truss?:

http://bluetorchfab.com/store/product_i ... cts_id=163

This is a SRW housing, right? I might be interested in getting this to do a 4 link in the Blazer, but I think I would rather find a Eaton.

When are you headed back to town?
James C.

97 K2500HD 6.5/4L80E/NP241/9.5/14BFF

86'ish S10 Blazer LT1/4L60E/ORD Doubler/D60/14BFF
User avatar
Billet Benny
Posts: 398
Joined: Fri Jan 07, 2005 7:30 pm
Location: Sinking Creek

Post by Billet Benny »

James,
That is the exact truss system. It is a srw housing. Here it is.

I am back right now.. but can get it whenever.
-B
Attachments
BTF 14 Bolt Truss and Housing
BTF 14 Bolt Truss and Housing
DSCN0150.jpg (93.22 KiB) Viewed 7989 times
BTF 14 Bolt Truss and Housing
BTF 14 Bolt Truss and Housing
DSCN0149.jpg (94.56 KiB) Viewed 7989 times
Benny
'98 Taco
'05 Taco
'00 Cummins
User avatar
Username
Posts: 172
Joined: Wed Dec 15, 2004 9:59 am
Location: passed out on the couch

Post by Username »

What is the length on that drag link?
User avatar
Billet Benny
Posts: 398
Joined: Fri Jan 07, 2005 7:30 pm
Location: Sinking Creek

Post by Billet Benny »

Brian,
I'll get that info next time I head down... I'll also dig out the draglink ends for it.
-B
Benny
'98 Taco
'05 Taco
'00 Cummins
User avatar
jonesy
Posts: 720
Joined: Sat Jan 14, 2006 12:16 am
Location: Blacksburg

Post by jonesy »

i really want all of your 14bff stuff .... hubs, carrier, shafts, housing ... ALL of it....

too bad i aint got shit for money.
User avatar
Billet Benny
Posts: 398
Joined: Fri Jan 07, 2005 7:30 pm
Location: Sinking Creek

Post by Billet Benny »

jonesy wrote:i really want all of your 14bff stuff .... hubs, carrier, shafts, housing ... ALL of it....

too bad i aint got shit for money.
Haha, I know I'm driving your jeep, but damn.. BTW, it's a raging POS and I only slid into one intersection so far. I do appreciate having it though, it's fun.

You got a complete 14 bolt what you need all the parts for??
Benny
'98 Taco
'05 Taco
'00 Cummins
cootees
Posts: 54
Joined: Thu Jan 11, 2007 4:26 pm
Location: Roanoke, Va.
Contact:

Post by cootees »

have any pics of the bike?
- 90 4Runner 2dr
User avatar
jonesy
Posts: 720
Joined: Sat Jan 14, 2006 12:16 am
Location: Blacksburg

Post by jonesy »

Billet Benny wrote:
jonesy wrote:i really want all of your 14bff stuff .... hubs, carrier, shafts, housing ... ALL of it....

too bad i aint got shit for money.
Haha, I know I'm driving your jeep, but damn.. BTW, it's a raging POS and I only slid into one intersection so far. I do appreciate having it though, it's fun.

You got a complete 14 bolt what you need all the parts for??
i need the hubs so i dont have to bother beadblasting and painting mine. need the shafts for spares. need the carrier for a spare (gonna shave the 538 gearset so i would like to have a spare to carry with me in case of boomage). need the 1410 yoke because 1350 sucks.


and yeah .... that bitch will slide from here to roanoke lol ....

if you want to hold onto everything for a year or twelve then ill buy it lol :flipoff2:
Post Reply