HENRY

Post by **shmoken875** » Fri Feb 16, 2007 5:55 pm

there is a green 97+ xj in the back of D&Ms lot (past the white one with the camaro on top) front clip looks fine, you might wanna check it out. I think I'm goin monday morning to snatch the door off of it and maybe the axleshafts.

Post by **hklvette** » Fri Feb 16, 2007 10:17 pm

Thanks for the line Randy. I'll be going by tomorrow and see what (other than the front clip) I can use off of it. In other news, I'm still working on patching up the cooler lines. I cut off the crimped part tonight, but it still leaks at the connections by the radiator. I'll get some better fittings tomorrow and see if that helps.

P.S. can you post directions to D&M in the none yards sticky in the tech section? Thanks.

Post by **Arya Ebrahimi** » Fri Feb 16, 2007 10:51 pm

That's the same one I told you about at the meeting

Post by **hklvette** » Fri Feb 16, 2007 10:53 pm

Arya Ebrahimi wrote: That's the same one I told you about at the meeting

I'm supposed to remember things after two days? :lol2:

Post by **shmoken875** » Sat Feb 17, 2007 12:13 pm

Arya Ebrahimi wrote: That's the same one I told you about at the meeting

I told him not to trust a damn word that comes out of your mouth

Lukipela · Post by **Lukipela** » Mon Feb 19, 2007 9:45 am

Hey Randy are the wheels being sold on that xj and if so you think he will sell just one cuz thats all i need.

Post by **Arya Ebrahimi** » Mon Feb 19, 2007 11:11 am

Lukipela wrote:Hey Randy are the wheels being sold on that xj and if so you think he will sell just one cuz thats all i need.

Dude, you obviously haven't been to D&M. He would sell you one spoke from one of the wheels if that's what you needed

I think the way they see it is, anything they can sell before it goes to the crusher is better than not selling anything at all.

I'm sure he's got an XJ wheel or 30 you could buy.

Ary

Lukipela · Post by **Lukipela** » Mon Feb 19, 2007 11:26 am

sweet well then where are they located or directions to D&M needed

Post by **shmoken875** » Mon Feb 19, 2007 11:40 am

Lukipela wrote:sweet well then where are they located or directions to D&M needed

If you pull a bearing throw the axle nut, cotter pin, axle nut retainer, and the three bearing bolts in the center consol or something please, I'd like to pull the shafts off it, and have a complete ready to go ready to bolt in spare shaft set. I already have 2 extra hub unit bearings, but I need the hardware. I might be going early wednesday morning or 130ish if you're interested

Lukipela · Post by **Lukipela** » Mon Feb 19, 2007 12:44 pm

can you go later wed. like around 4 cuz i got a class at 2:30 but 1 to 1:30 would be fine as long as we did not stay there to long. im free from 12:15 till 2:30 so in there is great.

Post by **hklvette** » Mon Feb 19, 2007 12:52 pm

when you go wednesday let me know if the green xj still has the parts i need on it. the earliest i can go pick them up is friday if i take the afternoon off.

Lukipela · Post by **Lukipela** » Mon Feb 19, 2007 2:03 pm

i might be getting a wheel from hutch so i will let you know if im going or not wed.

Lukipela · Post by **Lukipela** » Tue Feb 20, 2007 5:02 pm

im not going wed. cuz im getting a wheel from hutch but next time you are going let my know Randy cuz i would like to see what they got.

Post by **shmoken875** » Tue Feb 20, 2007 6:44 pm

yea I'm probly going in the morning anyways