Spindle Puller

Post by **Yoda** » Fri Apr 20, 2007 8:24 pm

Is there such a thing? Im breaking down the D44 while im at home and cant get the damn spindle to budge and im pretty sure there is nothing holding it on cept for a tight rust seal maybe. I dont wanna bang on it too hard as the surface is smooth where the bearings sit on it.

Post by **Leach** » Fri Apr 20, 2007 9:59 pm

Just grab a 2x4 and hit against that on the spindle. I have never seen a spindle puller but you could prolly make a slide hammer work somehow. But the 2x4 will be your best bet. And swing hard. Just make sure the 6 bolts or whatever are off and swing away.

YouTube · Post by **TerryD** » Fri Apr 20, 2007 10:01 pm

rubber coated dead blow hammers work excelent in that situation....ask verticleTRX....lol :lol2:

Vert: are you sure that's the way to do that?!?!?

TerryD: came off didn't it??

Post by **Yoda** » Fri Apr 20, 2007 10:50 pm

thanks for the advice, i figured that was the way to do it. just wanted to make sure before i went breaking stuff.

Post by **Yoda** » Fri Apr 20, 2007 11:14 pm

didnt seem to work, am i doing something wrong or am i just not punishing it enough

i removed the studs and all thats left is the spindle the knuckle the seals between the spindle and outer, and the outer and inner shafts, it should come off now shouldnt it

Post by **Leach** » Fri Apr 20, 2007 11:29 pm

Yea, but they can get frozen to the knuckle. If you have any heat you could try that. And you might seriously have to beat the ever loving poop outta it.

Post by **Yoda** » Fri Apr 20, 2007 11:35 pm

sweeeet i need a vent for all my anger from this week

Post by **Leach** » Fri Apr 20, 2007 11:53 pm

Haha there ya go. Just have fun, and dont deform the spindle. Use wood or a dead blow.

Post by **Steinberg** » Sat Apr 21, 2007 2:46 am

leach was halfway there. use a 2x4 and a big fawking hammer and wail on it

I thought that was what I said

YouTube · Post by **TerryD** » Sat Apr 21, 2007 8:54 am

swing like you're aimin for the fence.....feels good.....

Post by **Brett** » Tue Apr 24, 2007 12:37 pm

Try coating it with pb blaster about 10 times and tap. Let sit for a while. Try going at it from the back side with a chisel. Good luck.

Brett

Website · Post by **tsmall07** » Tue Apr 24, 2007 12:56 pm

Steinberg wrote:leach was halfway there. use a 2x4 and a big fawking hammer and wail on it

x2

It took me 3 days to get the spindle off my f150. I tried everything listed above, and nothing worked until I got the sledge with a piece of wood to soften the blow.

Post by **Yoda** » Tue Apr 24, 2007 2:04 pm

ive tried all of this so far, but apparently not enough

i will bang a little harder when i get back home. i will have more anger to let out. did i mention i hate EngE and its complete lack of applicability toward CEE? sophmore year will hopefully be more purposeful.

Post by **VerticalTRX** » Tue Apr 24, 2007 4:47 pm

TerryD wrote:rubber coated dead blow hammers work excelent in that situation....ask verticleTRX....lol

Vert: are you sure that's the way to do that?!?!?

TerryD: came off didn't it??

Yeah, on the easy spindle. The hard one would not come of so it had to be sacrificed. About ten full swing blows with a 9lb spitting maul got it off, it was trash though. The option was either that, or cut it off with a torch, luckily I had a spare axle to rob a good spindle off. Not to scare you or anything.

Website · Post by **tsmall07** » Tue Apr 24, 2007 5:50 pm

Yoda wrote: sophmore year will hopefully be more purposeful.

Wouldn't count on it. Thats why I'm in BC instead. That and the fact that my grades weren't near good enough to get into Engineering...